Plumbing Ac & Heating checkup $39.95

Plumbing Air Conditioning Repairs Start At $39.95

Silver Fox Plumbing AC & Heating provide professional high quality friendly Service - Installs – Repairs – Replace - Relocate for Central Air Conditioning System, AC, Heat Pump, Furnace, Swamp Cooler, Evap, Gas Electric Water Heater, Garbage Disposal, Faucet, Sink, Tub, Toilet, Shower, Kitchen Bath, Water Main, Valve, Hose Bib, Re-Pipe, Slab Leaks, Sewer Drain, Water Pipe Leaks for the Tempe metro area including Tempe, Tempe, Tempe, Peoria, Glendale, Anthem, Care Free, Cave Creek, Sun City, Paradise Valley, Biltmore, Arcadia, Litchfield, Young Town, Gilbert, Chandler, Tempe, Fountain Hills, Goodyear areas...

Silver Fox Plumbing AC & Heating provide professional high quality Installs - Repairs - Replace - Relocate for:

Tempe AZ AC Duct Repairs Installtion Install Tips

Sizing and Installation

Your new heating and cooling system should be a custom fit for your home. Sizing and a handful of other installation practices can dramatically affect how well your new equipment will deliver comfort and savings. Expect to pay a little more for a good contractor who follows these practices.

Calculate the size of equipment

Seal and insulate ducts in attics and crawlspaces

Check and correct air flow

Proper refrigerant charging

Equipment placement

Calculate the size of equipment

For starters your new furnace, boiler, heat pump or air conditioner should be sized to fit your home. You can request a copy of the design load calculation used to determine the right size of equipment for your home. A good contractor will not size your equipment solely on the square footage of your house or assume that your existing equipment was sized properly in the first place. Proper equipment sizing is based your home's heat loss during cold weather and heat gains during warm weather. For more information about sizing use the new Central Air Conditioner Sizing Tutorial.

To complete the design load calculation the contractor will need to take measurements during the initial visit to your home and ask you some questions. The calculation is usually done using software, and should be based on professional guidelines such as Manual J from the Air Conditioning Contractors of America (ACCA) or similar method. Oversized equipment can cause reduced comfort and excessive "air" noise. Oversizing will shorten the life of the equipment by causing it to cycle on and off more frequently than a properly-sized unit. Undersized equipment, with airflow that is too low, can reduce the efficiency of the air distribution and accelerate wear on system components, leading to earlier failure.

After the design load calculation is completed, ducts, supply registers, and return grilles can be sized and selected using professional guidelines in ACCA's Manual D or similar method.

Seal and insulate ducts in attics and crawlspaces

If you're installing a central air conditioner, furnace or heat pump ask your contractor about the condition of your air ducts. A good contractor should be able to test your air ducts to identify and seal leaks.

Duct sealing should be done by a professional using mastic, metal-backed tape or aerosol-based sealing.

In some instances, your contractor may advise you that it is necessary to replace or add ducts. If there are insufficient supply registers or return air grilles in your home, it may be necessary to install additional ducts to accommodate the need for registers or grilles. When possible ducts should be located within conditioned space. If the ducts must be in unconditioned space (attic or crawlspace) they should be insulated.

Check and correct airflow

For central air conditioners, furnaces or heat pumps there is an optimal air flow for comfort and savings.

If airflow is too high, duct leakage increases and the temperature at the register is not sufficient for optimal home comfort.

If airflow is too low, distribution efficiency drops and accelerates the wear on system components leading to premature failure.

A good contractor will test the air flow of your heating and cooling system and make adjustments for optimal performance. Typically, testing and adjustments should be done after duct leakage repairs have been completed.

Proper refrigerant charging

If your are installing a new central air conditioner or heat pump you should know that recent field studies suggest that approximately 75% of installed cooling equipment may have incorrect amount of refrigerant. Incorrect refrigerant level can lower efficiency by 5 to 20% and can ultimately cause premature component failure, resulting in costly repairs that could have been prevented. A good contractor will use one of three methods, recommended by equipment manufacturers, to verify the correct refrigerant level. These methods include super-heat, sub-cooling, or weigh. Ask your contractor how they verify the refrigerant level is correct.

In addition, you should know that since 1992, in order to protect the earth's atmosphere (ozone layer), all technicians must be certified to handle refrigerant. Ask them to show you proof of refrigerant handling certification.

Equipment placement

Placement of new equipment is unique for every home, but a good contractor should follow manufacturer's installation instructions for best results. For example, Indoor equipment should be installed in conditioned space, or a space that is well insulated. The Outdoor compressors should be placed out of the sun and kept free of debris. Equipment should be installed in an accessible area for easy maintenance. Allow plenty of room for free airflow on all sides of the equipment. Thermostats should be placed away from direct sunlight, drafts, doorways, skylights and windows.

Areas Serviced…

The Tempe metro area including: Aguila, Ak-Chin Village, Apache Junction, Tempe Foot Hills, Anthem, Arcadia, Arizona, Arrowhead, AZ, Bell Road, Biltmore, Tempe, Camelback, Casa Grande, Cave Creek, Care Free, Chandler, Deer Valley, Dobson Ranch, Double Tree Ranch, Encanto, Estrella, El Mirage, Fountain Hills, Gilbert, Glendale, Gold Canyon, Goodyear, Guadalupe, Hayden, Higley, Indian School, Laveen, Litchfield Park, Luke AFB, Maricopa County, Maryvale, McCormick Ranch, Tempe, Moon Valley, Morristown, New River, Palo Verde, Paradise Valley, Peoria, Tempe, Ray Road, Rio Verde, Tempe, South Mountain, Sun Lakes, Sun City, Surprise, Tempe, Tolleson, Tonopah, Tortilla Flat, Tramonto, Youngtown, Waddell areas...